3M MT16H210F-478-RD Manuel de service télécharger pdf (Page 5)

IMPORTANT! For the best protection, brush aside hair around the ears so the ear cushions t snugly

against the head. Spectacle frames should be as thin as possible and t close to the head.

TECHNICAL DATA (B)

(B:1) Attenuation values, SNR

The attenuation values and noise levels for the hearing protector have been tested and approved

according to EN 352-4 2001, EN 352-6 2002 and applicable parts of EN 352-1 2002. Certicate

issued by INSPEC (Registered Number 0194), Upper Wingsbury Courtyard, Wingrave, Aylesbury,

Buckinghamshire, HP22 4LW, United Kingdom.

Explanation of the attenuation value table

1. Weight

2. Frequency

3. Average attenuation

4. Standard deviation

5. Expected attenuation

(B:2) Input signal level/usage time

Maximum permitted audio signal in relation to usage time.

To prevent harmful levels, the input signal must not exceed the stated values (average speech signal

level). The earphone level for long-term average value of music and speech is measured at max 82

dB (A) equivalent noise level according to the PPE directive.

1. Hrs/day

2. Average level/electrical signal X=140,2 mV

(B:3) Sound exposure when using the auxilary input

1. Level under the ear-muff [dB(A)]

2. Input voltage [mVrms]

(B:4) Criterion level

The criterion level is the noise (mesured as A-weighted sound pressure level) outside the hearing

protector that gives 85 dB(A) inside. The outside level depends on the type of noise: H is high

– frequency dominated noise, M is noise that is not dominated by any given frequency and L is low

– frequencydominated noise.

USE (C)

(C:1) Open the headband.

(C:2) Slide out the cups. Tilt the top of the cup out, as the wire must be placed on the outside of

the headband.

(C:3) Adjust the height of the cups by pulling the cup up or down while pressing the headband

down.

(C:4) The headband should lie across the top of the head.

(C:5) Press the cups in before collapsing. Leave about 4 mm (1/8”) of the headband wire visible.

(C:6) Collapse the headband. Check that the ear cushions are not creased and that they lie at

against one another. NOTE! When the headband is to be collapsed, make sure to unplug the

audio input jack (A:11)

(C:7) On and off Press the centre button and hold for at least 2 seconds.

(C:8) Increase volume Press the upper (+) button.

(C:9) Decrease volume Press the lower (-) button.

STORAGE (D)

Do not store this hearing protection in temperatures exceeding +55°C, for example inside a windscreen

or a window.

ATTENTION: When the headband is to be collapsed, make sure to unplug the audio input jack (A:

(D:1) WRONG All guide wires must be pushed in correctly before the headband is collapsed.

(D:2) RIGHT The ear cushions should lie at against each other.

(D:3) WHEN DAMP Turn the cups outwards. Remove the ear cushions to allow the attenuation

cushions and electronics to dry. Reassemble. See the CARE section.

CARE (E)

CLEANING

Clean/disinfect the cups, headband and ear cushions regularly with soap and warm water.

Note: Do not immerse the cups in water!

REMOVING/REPLACING OUTER SHELLS

To remove outer shells:

(E:1) Insert tool or your ngers under the edge of the clip and pull it out 3-4 mm

(E:2) Press/slide the clip downward. Remove the shell

To put outer shells back into position:

(E:3) Make sure the clip is fully pressed back

Put the shell in place from top to bottom making sure the hook on the top of the shell (E:4)

t into the hole on inner cup (E:5).

(E:6) When the shell is in place, press/slide the clip upwards

REPLACING THE BATTERIES

Remove the right hand outer shell, for instruction please see Removing/Replacing outer shells.

Replace the batteries and then put the outer shell back into position, for instructions please see

Removing/Replacing outer shells.

1 2 3 4 5 6 7 8 9 10 ... 81 82

Commentaires sur ces manuels

Pas de commentaire

3M MT16H210F-478-RD Manuel de service Page 5

Commentaires sur ces manuels

Produits connexes et manuels pour Casques d'écoute 3M MT16H210F-478-RD